Instructions: Large Bottom Drawer for Apollo / Echo 36 & 48 / Voyager 42

Step-by-step instructions to install your INOVATIV Large Bottom Drawer for Apollo, Echo 36 & 48, and Voyager 42 workstation carts.

Tools Needed: 
5/32 Allen Key, 7/16 or 11mm Socket or Wrench, 1/4” Drill Bit and Drill for Voyager Installs

Box Contents:

NOTE: DO NOT PULL CARPET BACK TO ACCESS HOLES. 
POKE HOLES THROUGH CARPET USING A SHARP POINTED TOOL.

Apollo Workstation Carts

If you are installing a bottom drawer to an Apollo cart, please use the below templates to determine location for mounting. NOTE: You will NOT need the provided 1/4-20 Nylon Locknuts to mount an Apollo bottom drawer. All Apollo carts have threaded inserts installed in the bottom shelf.

1. Using the below template as a reference, remove, by unscrewing, the 6 existing 1/4-20 bolts from the underside of the bottom shelf. These 6 are currently screwed into the threaded inserts in the location of the bottom drawer.

2. Large Bottom Drawer Brackets on the bottom side of the lower shelf.

3. Using the provided 1/4-20, 5/8" Long BHA Bolts, slowly begin to mount the drawer brackets to the existing threaded inserts located in the bottom shelf.

4. Connect the Large Bottom Drawer to the Large Bottom Drawer Bracket by aligning the slides and pushing in. Check fit by sliding the drawer in and out, it should be smooth.

5, Connect the Short Lock Stop to the centered hole in the bottom shelf again using the template below as reference. You will need to punch through the carpet and pass the bolt through the bottom shelf into the lock stop – do not tighten and be sure to use the loctite thread-locker provided.

6. Make sure the Combo Lock locking lever is in its unlocked position. Close the drawer, rotate the lock to its locked position and slide the Short Lock Stop as close to the locking lever as possible and then tighten.

7. Reset your Combo Lock.

Apollo 40

Apollo 52

Echo and Ranger 36/48 Workstation Carts

If you are installing a bottom drawer to an Echo or Ranger cart, there are existing hole locations specifically for the bottom drawer. You will need to punch through the bottom carpet, allowing pass-through of the mounting hardware.

1. Place the Large Bottom Drawer Brackets on the bottom side of the lower shelf.

2. Pass the 1/4-20, 5/8" Long BHA Bolt through the carpet into and through the holes of the Large Bottom Drawer Brackets.

3. Attach the 1/4-20 Nylon Locknuts to the 1/4-20 bolts.

4. Connect the Large Bottom Drawer to the Large Bottom Drawer Brackets by aligning the slides and pushing in. Check fit by sliding the drawer in and out, it should be smooth.

5. Make sure the Combo Lock locking lever is in its unlocked position. Connect the Short Lock Stop to the centered hole in the bottom shelf – do not tighten and be sure to use the loctite thread-locker provided.

6 .Close the drawer and turn the Combo Lock to its locked position. Slide the Short Lock Stop as close to the locking lever as possible and then tighten.

7. Reset your Combo Lock.

Voyager 42 Workstation Carts

If you are installing a bottom drawer to a Voyager cart, there are existing pilot-hole locations on the bottom shelf specifically to mount the bottom drawer. You will need a 1/4” drill bit and drill to increase the pilot-hole to the correct size for pass-through of mounting hardware.

1. Using a 1/4 “ drill bit, increase the size of the pilot holes located on the underside of the bottom shelf. Note: You will drill directly through the bottom carpet.

2. Place the Large Bottom Drawer Brackets on the bottom side of the lower shelf.

3. Pass the 1/4-20, 5/8" Long BHA Bolts through the carpet into and through the holes of the Large Bottom Drawer Brackets.

4. Attach the 1/4-20 Nylon Locknuts to the 1/4-20 bolts.

5. Connect the Large Bottom Drawer to the Large Bottom Drawer Brackets by aligning the slides and pushing in. Check fit by sliding the drawer in and out, it should be smooth.

6. Make sure the Combo Lock locking lever is in its unlocked position. Connect the Short Lock Stop to the centered hole in the bottom shelf – do not tighten and be sure to use the loctite thread-locker provided.

7 . Close the drawer and turn the Combo Lock to its locked position. Slide the Short Lock Stop as close to the locking lever as possible and then tighten.

8. Reset your Combo Lock.

SETTING THE COMBINATION DRAWER LOCK

1. The factory combination is set at “0-0-0”.
2. The combination must be set on the factory number prior to resetting.
3. On the underside outer edge of the lock there is a hole for the code reset button. Rotate the face of the cam until the code reset button comes into view.
4. Depress the pin with a paper clip and keep it pushed in.
5. Set your personal combination by turning dials to the desired combination digits.
6. Release the reset button and your combination is set.
7. To lock, rotate lock to “locked” position. Rotate one or more digit dials after lock is closed. To open lock, turn dials to personal combination.